   KPG-49D Help File  Version 3.01
   File name: KPG49D_3.HLP

2.00    May/08/1999    Add TK-980/981


 New File Help (CLEAR FILE)
This function clears all data currently shown in the channel 
information window and restores the defaults.

1. Select "New" then press [Enter], or simply press [N].
   A warning message appears.
2. Select "[Ok]" or "[Cancel]" then press [Enter], or simply press [O] 
   or [C].

 Load Help
The Load function reads a data file saved on a hard disk or floppy 
disk, then writes the file into the buffer memory of your computer.
You may change the loaded file, write it to the transceiver, or print 
it out.

1. Select "Load" then press [Enter], or simply press [L].
   The "Drive & Path" window opens, and displays the currently 
   selected drive and path name.
2. Type the drive and path name of the desired file, then press 
   [Enter].
   The "Directory" window opens and displays the name(s) of the 
   file(s) on that path.
   Data files have "DAT" extensions.

Note 1:  If the entered drive does not contain a disk, an error 
         message appears.
         Press any key, insert the correct disk in the specified 
         drive, then press [Enter].
Note 2:  If the entered drive or path does not exist, an error message 
         appears.
         Press any key, correct the drive or path name, then press 
         [Enter].
Note 3:  If no file is found under the drive and path name, an error 
         message appears.
         Press any key, correct the drive and path names, then press 
         [Enter].

3. Select the desired file name, then press [Enter].
   The "Load file name" window opens.
4. Select "[Ok]" or "[Cancel]" then press [Enter], or simply press [O] 
   or [C].

 Save Help
The Save function saves the created or revised file to the drive, 
path, and file names previously selected (or default).

1. Select "Save (=F4)" then press [Enter], or simply press [S] or 
   [F4].  The "Save file name" window opens.
   
Note:  If the same file name exists under the current path, a warning 
       message appears.

2. Select "[Ok]" or "[Cancel]" then press [Enter], or simply press [O] 
   or [C].

 Save as Help
The save As function saves the current file to the drive, path, and 
file names that you specify.

1. Select "save As" then press [Enter], or simply press [A].
   The "Drive & Path" window opens and displays the currently selected 
   drive and path names.
2. Type the desired drive and path names, then press [Enter].
   The "Save file name" window opens.

Note 1:  If the entered drive does not contain a disk, an error 
         message appears.
         Press any key, insert the correct disk in the specified 
         drive, then press [Enter].
Note 2:  If the entered drive or path does not exist, an error message 
         appears.
         Press any key, correct the entered drive or path name, then 
         press [Enter].

3. Type the desired file name, then press [Enter].
   The "Save file name" window opens.

Note 1:  If the same file name exists under the specified path, a 
         warning message appears.
Note 2:  If you prefer, press [F9] to open the "Directory" window.
         Select the desired file name, then press [Enter] twice.

4. Select "[Ok]" or "[Cancel]" then press [Enter], or simply press [O] 
   or [C].

 Delete Help
The Delete function allows you to delete unnecessary files from the 
desired disk thereby freeing up disk space.

1. Select "Delete" then press [Enter], or simply press [D].
   The "Drive & Path" window opens and shows the currently selected 
   drive and path name.
2. Type the desired drive and path name, then press [Enter].
   The "Directory" window opens.

Note 1:  If the entered drive does not contain a disk, an error 
         message appears.
         Press any key, insert the correct disk in the specified 
         drive, then press [Enter].
Note 2:  If the entered drive or path does not exist, an error message 
         appears.
         Press any key, correct the drive or path name, then press 
         [Enter].
Note 3:  If no file exists under the drive and path name, an error 
         message appears.
         Press any key, correct the drive and path names, then press 
         [Enter].

3. Select a file name using the up- or down-arrow key, then press 
   [Enter].
   The "Delete file name" window opens.
4. Select "[Ok]" or "[Cancel]" then press [Enter], or simply press [O] 
   or [C].
   After erasing the last file in the current directory, the channel 
   information window opens; otherwise the "Directory" window opens 
   again.
5. Repeat step 3 and 4 to delete all unnecessary files.

 Print Help
The Print function directs data to the printer.
The data may have been created, loaded from a disk, or read from the 
transceiver.
The information that you can print includes the following:

* File name
* Model name
* Optional features
* Key assignment
* Scan information
* DTMF
* 2-Tone (Conventional format only)
* FleetSync
* Test frequency
* Embedded message
* Group information (Conventional format only)
* System information (Trunking format only)

1. Select "Print (=F5)" then press [Enter], or simply press [P].
   The "Print out list" window opens.
2. Press the up- or down-arrow key to highlight the setting to be 
   changed.
3. Press [SPACE BAR] or [F2] to select "[Yes]" for printing or "No" 
   for canceling the print operation.
4. At the bottom of the Print out list window,
   type the desired start group, then press [Enter].
   Type the desired  end group, then press [Enter].
5. Press [F5] to open the "Edit data print out" window.
6. Select "[Ok]" or "[Cancel]".

Note:  If the printer is not ready, an error message will appear.
       Check the printer, then select "[Ok]" or "[Cancel]".

 Go to Dos Help
The "Go to dos" function allows you to temporarily exit the program 
and go back to the DOS prompt.

1. Select "Go to dos" then press [Enter], or simply press [G].
   The "Type EXIT to return to FPU" message and the DOS prompt appear.
2. To restore the previous screen, type "exit" then press [Enter].

Note:  The KPG-49D software can support this command only when your 
       computer has sufficient memory.

 Exit Help
The eXit function quits the program completely and restores the DOS 
prompt.

1. Select "eXit (=F3)" then press [Enter], or simply press [X].
   The "Return to DOS!" window opens.
2. Select "[Ok]" or "[Cancel]" then press [Enter], or simply press [O]
   or [C].

 TK-780 Help
Frequency range
 1: 146 - 174MHz
 2: 136 - 162MHz

This VHF transceiver can be programmed with up to 32 systems and up to 
250 groups (Trunking format) or up to 250 channels in various 
combinations of groups (Conventional format).

1. Select "TK-780" using the up- or down- arrow key, then press 
   [Enter].
   The "VHF" window opens.
2. Select desired function.
   The "Option Board" window opens.
3. If an option board (Voice Scrambler or ANI board) has been 
   installed, select desired function ; otherwise select "None".
   The "Radio Format" window appears.
4. FleetSync enhanced option is not available as standard. It enables
   GPS, Short Messaging, etc..
   Select "[Yes]" or "[No]", or simply press [Y] or [N].
5. Select "Conventional" or "Trunking".
   A confirmation window appears.
6. Select "[Ok]" or "[Cancel] then press [Enter], or simply press [O] 
   or [C].

Note:  When switching from a VHF model to a UHF model, or changing a 
       radio format or vice versa, a warning message appears to remind 
       you that all data or frequency data currently displayed will be 
       cleared from the screen.
       Select "[Ok]" or "[Cancel]".

 TK-880 Help
Frequency range
 1: 450 - 490MHz
 2: 485 - 512MHz
 3: 400 - 430MHz

This UHF transceiver can be programmed with up to 32 systems and up to 
250 groups (Trunking format) or up to 250 channels in various 
combinations of groups (Conventional format).

1. Select "TK-880" using the up- or down- arrow key, then press 
   [Enter].
   The "UHF" window opens.
2. Select desired function.
   The "Option Board" window opens.
3. If an option board (Voice Scrambler or ANI board) has been 
   installed, select desired function ; otherwise select "None".
   The "Radio Format" window appears.
4. FleetSync enhanced option is not available as standard. It enables
   GPS, Short Messaging, etc..
   Select "[Yes]" or "[No]", or simply press [Y] or [N].
5. Select "Conventional" or "Trunking".
   A confirmation window appears.
6. Select "[Ok]" or "[Cancel] then press [Enter], or simply press [O] 
   or [C].

Note:  When switching from a UHF model to a VHF model, or changing a 
       radio format or vice versa, a warning message appears to remind 
       you that all data or frequency data currently displayed will be 
       cleared from the screen.
       Select "[Ok]" or "[Cancel]".

Caution! : Frequencies from 406.0 to 406.1MHz are reserved in the US
           for emergency locator beacons. This radio is not intended
           for operation on these frequencies in the US.

 TK-280 Help
Frequency range
 1: 146 - 174MHz
 2: 136 - 162MHz

This VHF transceiver can be programmed with up to 32 systems and up to 
250 groups (Trunking format) or up to 250 channels in various 
combinations of groups (Conventional format).

1. Select "TK-280" using the up- or down- arrow key, then press 
   [Enter].
   The "VHF" window opens.
2. Select desired function.
   The "Option Board" window opens.
3. If an option board (Voice Scrambler or ANI board) has been 
   installed, select desired function ; otherwise select "None".
   The "Radio Format" window appears.
4. FleetSync enhanced option is not available as standard. It enables
   Short Messaging, etc..
   Select "[Yes]" or "[No]", or simply press [Y] or [N].
5. Select "Conventional" or "Trunking".
   A confirmation window appears.
6. Select "[Ok]" or "[Cancel] then press [Enter], or simply press [O] 
   or [C].

Note:  When switching from a VHF model to a UHF model, or changing a 
       radio format or vice versa, a warning message appears to remind 
       you that all data or frequency data currently displayed will be 
       cleared from the screen.
       Select "[Ok]" or "[Cancel]".

 TK-380 Help
Frequency range
 1: 450 - 490MHz
 2: 470 - 512MHz
 3: 400 - 430MHz

This UHF transceiver can be programmed with up to 32 systems and up to 
250 groups (Trunking format) or up to 250 channels in various 
combinations of groups (Conventional format).

1. Select "TK-380" using the up- or down- arrow key, then press 
   [Enter].
   The "UHF" window opens.
2. Select desired function.
   The "Option Board" window opens.
3. If an option board (Voice Scrambler or ANI board) has been 
   installed, select desired function ; otherwise select "None".
   The "Radio Format" window appears.
4. FleetSync enhanced option is not available as standard. It enables
   Short Messaging, etc..
   Select "[Yes]" or "[No]", or simply press [Y] or [N].
5. Select "Conventional" or "Trunking".
   A confirmation window appears.
6. Select "[Ok]" or "[Cancel] then press [Enter], or simply press [O] 
   or [C].

Note:  When switching from a UHF model to a VHF model, or changing a 
       radio format or vice versa, a warning message appears to remind 
       you that all data or frequency data currently displayed will be 
       cleared from the screen.
       Select "[Ok]" or "[Cancel]".

Caution! : Frequencies from 406.0 to 406.1MHz are reserved in the US
           for emergency locator beacons. This radio is not intended
           for operation on these frequencies in the US.

 TK-980 Help
Frequency range
 FCC Channel No. 1 - 911

This UHF transceiver can be programmed with up to 32 systems and up to 
250 groups.

1. Select "TK-980" using the up- or down- arrow key, then press 
   [Enter].
   The "800MHz" window opens.
2. Select desired function.
   The "Option Board" window opens.
3. If an option board (Voice Scrambler or ANI board) has been 
   installed, select desired function ; otherwise select "None".
   A confirmation window appears.
4. FleetSync enhanced option is not available as standard. It enables
   GPS, Short Messaging, etc..
   Select "[Yes]" or "[No]", or simply press [Y] or [N].
5. Select "[Ok]" or "[Cancel] then press [Enter], or simply press [O] 
   or [C].

Note:  When switching the Band of model,
       a warning message appears to remind 
       you that all data or frequency data currently displayed will be 
       cleared from the screen.
       Select "[Ok]" or "[Cancel]".

 TK-981 Help
Frequency range
 FCC Channel No. 1 - 399

This UHF transceiver can be programmed with up to 32 systems and up to 
250 groups.

1. Select "TK-981" using the up- or down- arrow key, then press 
   [Enter].
   The "900MHz" window opens.
2. Select desired function.
   The "Option Board" window opens.
3. If an option board (Voice Scrambler or ANI board) has been 
   installed, select desired function ; otherwise select "None".
   A confirmation window appears.
4. FleetSync enhanced option is not available as standard. It enables
   GPS, Short Messaging, etc..
   Select "[Yes]" or "[No]", or simply press [Y] or [N].
5. Select "[Ok]" or "[Cancel] then press [Enter], or simply press [O] 
   or [C].

Note:  When switching the Band of model,
       a warning message appears to remind 
       you that all data or frequency data currently displayed will be 
       cleared from the screen.
       Select "[Ok]" or "[Cancel]"

 TK-480 Help
Frequency range
 FCC Channel No. 1 - 911

This UHF transceiver can be programmed with up to 32 systems and up to 
250 groups.

1. Select "TK-480" using the up- or down- arrow key, then press 
   [Enter].
   The "800MHz" window opens.
2. Select desired function.
   The "Option Board" window opens.
3. If an option board (Voice Scrambler or ANI board) has been 
   installed, select desired function ; otherwise select "None".
   A confirmation window appears.
4. FleetSync enhanced option is not available as standard. It enables
   Short Messaging, etc..
   Select "[Yes]" or "[No]", or simply press [Y] or [N].
5. Select "[Ok]" or "[Cancel] then press [Enter], or simply press [O] 
   or [C].

Note:  When switching the Band of model,
       a warning message appears to remind 
       you that all data or frequency data currently displayed will be 
       cleared from the screen.
       Select "[Ok]" or "[Cancel]".

 TK-481 Help
Frequency range
 FCC Channel No. 1 - 399

This UHF transceiver can be programmed with up to 32 systems and up to 
250 groups.

1. Select "TK-481" using the up- or down- arrow key, then press 
   [Enter].
   The "900MHz" window opens.
2. Select desired function.
   The "Option Board" window opens.
3. If an option board (Voice Scrambler or ANI board) has been 
   installed, select desired function ; otherwise select "None".
   A confirmation window appears.
4. FleetSync enhanced option is not available as standard. It enables
   Short Messaging, etc..
   Select "[Yes]" or "[No]", or simply press [Y] or [N].
5. Select "[Ok]" or "[Cancel] then press [Enter], or simply press [O] 
   or [C].

Note:  When switching the Band of model,
       a warning message appears to remind 
       you that all data or frequency data currently displayed will be 
       cleared from the screen.
       Select "[Ok]" or "[Cancel]".

 Group Name Text Size Help
Enter the Text Size for the Group Name.
Maximum Group Name Text size is 10.
Then Channel Name Text Size becomes (10 - Group Name Text Size) of the
transceiver display.

Range  : Off (0) to 10 (steps of 1)
Default: Off

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2], or by directly entering a value.

 Sub LCD Display Help
Select the Sub LCD Display contents.

None   : Nothing is displayed on the Sub LCD.
Group  : The Sub LCD shows the Group number.
Channel: The Sub LCD shows the Channel number. (Conventional format)
System : The Sub LCD shows the System number. (Trunking format)
Default: None

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2].

Note 1  : Additional display characters.
          "HA" indicates Horn Alert function is ON. (Mobile only)
          "TA" indicates Talk Around function is ON.
          In order of precedence is;
          HA > TA

Note 2  : When System, Group or Channel number is set to the Sub LCD 
          display, displays System, Group or Channel number for 2 
          seconds after changing System, Channel or Group. Then 
          displays "HA", "TA" if it is set.

 Busy LED Help
Enable or disable the Busy LED function.
This function is only for Conventional format or Conventional system 
in Trunking format.

On     : The LED light green.
Off    : The LED does not lights green.
Default: On(Conventional format)/Off(Trunking format)

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2].

 Display Character Help
[Conventional format]
This function allows you to select either group number/channel number 
(Grp#/Ch#) or channel name for the transceiver display.

Grp#/Ch#    : Group and channel numbers appear on the transceiver 
              display.
Channel Name: Preprogrammed name in the "Ch Name" of the Channel Data 
              window appears on the transceiver display.
Default     : Channel Name

Note:  If "Grp Name" is selected but no group name is programmed for 
       the displayed group, the system#/group# will appear.

[Trunking format]
This function allows you to select either system number/group number 
(Sys#/Grp#) or group name (Grp Name) for the transceiver display.

Sys#/Grp# : System and group numbers appear on the transceiver 
            display.
Group Name: Preprogrammed name in the "Grp Name" column of the Group 
            Data window appears on the transceiver display.
Default   : Group Name

Note:  If "Channel Name" is selected but no channel name is programmed 
       for the displayed channel, the group#/channel# will appear.

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2].

Note:  If a programmable switch (A, B, C, Monitor, etc.) is set to 
       "Display Character", you can change the display style of 
       individual groups with this switch.

 Off Hook Decode Help
This function is only for mobile transceivers.
The transceiver is still tone squelched even though the microphone is 
in the off hook condition. (valid for QT, DQT, 2-Tone and DTMF decode)
2-Tone is only for Conventional format.

Enable : Decode signalling is active even if the microphone is in the
         off hook condition.
Disable: Decode signalling is disabled during off hook, squelch works 
         as carrier squelch.
Default: Disable

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2].

 Off Hook Horn Alert Help
This function is only for mobile transceivers.

[Trunking format]
The Horn Alert activates when the transceiver is called with
signalling even though the microphone is in the off hook condition.

[Conventional format]
The Horn Alert activates when the transceiver is called with option 
signalling even though the microphone is in the off hook condition.

Enable : Enable Horn Alert action is not controlled by microphone hook 
         status.
Disable: Disable Microphone must be on hook for Horn Alert action.
Default: Disable

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2].

 Horn Alert Time Help
This function is only for mobile transceivers.
This parameter is the time of Horn Alert relay switch action.

Range  : Off(0) to 30 (steps of 1)
Default: 4 sec

 Radio Password Help
This code can be up to 6 digits from 0 to 9 and is used to unlock a 
locked transceiver.

Enter the desired digits using the keyboard, then press [Enter].

How to unlock a locked transceiver

<Method 1: Using the keypad>
1. Enter the Radio Password from the numeric keys.
2. Press the SCN(Mobile)/S(Portable) key.

<Method 2 (Mobile) : Using the UP/DOWN key>
1. UP or DOWN the Group Up/Down (Conventional format) or 
   System Up/Down (Trunking format), and press the SCN key to select a
   number for a digit.
2. Repeat the previous procedure to complete entering the Radio 
   Password.
3. Press the SCN key again.

<Method 2 (Portable) : Using the tuning knob>
1. Rotate the tuning control knob, and press the S key to select a 
   number for a digit.
2. Repeat the previous procedure to complete entering the Radio 
   Password.
3. Press the S key again.

If the entered numbers are correct, the radio will be switched to the 
operation mode.  If not, the transceiver will return to the locked 
mode.

Note 1:  Entering an incorrect code causes the transceiver to output 
         an "Key Input Error Tone" and remains in "PASSWORD" state.
Note 2:  The user must enter each digit within a 10 second period, 
         otherwise the transceiver will clear the entered digits and 
         "PASSWORD" will reappear.

 Data Password Help
Password protection prevents unauthorized reading of the transceiver 
program data.  You can enter a maximum of 6 digits in the range of 0 
to 9.

Enter the required password with the keyboard, then press [Enter].

To read data from the password-protected transceiver, you must enter 
the correct password.  

Another Function (Clone Lock):
Password protection does not prevent writing data to a transceiver.  
Cloning mode can be disabled by setting "Optional features/Mode/Clone" 
to "Disable".  If "Optional features/Mode/Clone" is set to "Enable", 
this password also disables Clone mode unless the proper password is 
entered.

How to unlock a locked transceiver

<Method 1: Using the keypad>
1. Enter the Radio Password from the numeric keys.
2. Press the SCN(Mobile)/S(Portable) key.

<Method 2 (Mobile) : Using the UP/DOWN key>
1. UP or DOWN the Group Up/Down (Conventional format) or 
   System Up/Down (Trunking format), and press the SCN key to select a
   number for a digit.
2. Repeat the previous procedure to complete entering the Radio 
   Password.
3. Press the SCN key again.

<Method 2 (Portable) : Using the tuning knob>
1. Rotate the tuning control knob, and press the S key to select a 
   number for a digit.
2. Repeat the previous procedure to complete entering the Radio 
   Password.
3. Press the S key again.

If the entered numbers are correct, the radio will be switched to the 
clone mode and "CLONE MODE" will appear.  If not, the transceiver will 
return to the locked mode.

Note:  The user needs to enter each digit within a 10-second period, 
       otherwise the transceiver will clear the entered digits and 
       "CLONE LOCK" will reappear.

 Power On Text Help
This 12 alphanumeric message is displayed when switching on the radio.

Enter the required characters for the Power On Text.

 Signalling Help
Signalling "AND"/"OR" sets the audio unmute condition for any channel
programmed for 2-Tone,DTMF or MSK decode (Option Signalling).

AND    : "AND" requires both the valid Option Signalling and the
         programmed QT/DQT to be received for audio to unmute (and
         initiate an Option Signalling decode alert).
OR     : "OR" requires the programmed QT/DQT to be received for audio
         to unmute (an Option Signalling alert is only initiated if
         the proper Option Signalling is decoded).
Default: OR

Note : Alert tone for MSK decode is turned on/off by Control tone
       setting.

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR],
[F2], or [Shift]+[F2].

 Selective Call Alert LED Help
This selects whether or not the LED on the transceiver flashes
orange when a 2-Tone Call or DTMF Selective Call has occurred.
2-Tone is only for Conventional format.

Yes    : The LED flashes orange
No     : The LED does not flash
Default: Yes

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR],
[F2], or [Shift]+[F2].

 Clear to Transpond Help
The transceiver will wait when the channel is busy, then transponds 
when the channel becomes open. See the 2-Tone or DTMF menu for the 
Transpond feature.

Yes    : Enable the Clear to Transpond feature.
No     : Disable the Clear to Transpond feature.
Default: No

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2].


 Com 0(Mic. Jack) Help
This function selects the external serial port function at a
microphone jack (TXD/RXD). PC programming can be accepted regardless
of this setting.

None     : Disables the serial port
Data     : Enables the Serial port function for FleetSync serial data
           [FleetSync Enhanced option]
REM      : Enables the Serial port function for Remote Control Command
           serial data
Data+GPS : Enables the Serial port function for FleetSync serial data,
           also available to output the received GPS data via air.
           GPS data input must use Com 1 port.(mobiles only)
           [FleetSync Enhanced option] (Version 2.0 radio only)
Default  : None

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR],
[F2], or [Shift]+[F2].

 Com 1(Internal Port) Help
This function selects the external COM1 pin serial port function on
the KCT-19 accessory jack (TXD1/RXD1).

None     : Disables the serial port
REM      : Enables the Serial port function for Remote Control
           Command serial data
Data     : Enables the Serial port function for FleetSync serial data
           [FleetSync Enhanced option]
GPS      : Enables the Serial port function for GPS receiver unit
           NMEA0183 data input (RXD1). Also, it outputs the received
           GPS data from the mobiles (TXD1). (mobiles only)
           [FleetSync Enhanced option]
Data+GPS : Enables the Serial port function for FleetSync serial data,
           also available to output the received GPS data via air.
           GPS data input must use Com 1 port.(mobiles only)
           [FleetSync Enhanced option] (Version 2.0 radio only)
Default  : None

(see Service Manual for details)

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR],
[F2], or [Shift]+[F2].

 Com 2(Internal Port) Help
Mobile radio only. This function selects the external COM2 pin serial
port function on the KCT-19 accessory (RXD2(AHK)/TXD2(PTT)).

This function selects the external serial port function (TXD2/RXD2).
The mobiles have two external serial ports.

None         : Disables the serial port
AUX Hook/PTT : Enables the serial port function for AUX PTT or Hook
               switch signal
Data PTT     : Enables the serial port function for Data PTT 
               function. The Data PTT works as same as press the DTC
               and the PTT simultaneously. (Version 2.0 radio only)
REM          : Enables the Serial port function for Remote Control
               Command serial data
Data         : Enables the Serial port function for FleetSync serial
               data [FleetSync Enhanced option]
Data+GPS     : Enables the Serial port function for FleetSync serial
               data, also available to output the received GPS data
               via air.
               GPS data input must use Com 1 port.(mobiles only)
               [FleetSync Enhanced option] (Version 2.0 radio only)
Default      : None

(see Service Manual for details)

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR],
[F2], or [Shift]+[F2].

 Time Out Timer(TOT) Help
This selects the period of time users can continuously transmit.  
When the selected period elapses, the transceiver generates an "Alert" 
tone and stops transmitting.

Range  : 15 to 600 sec. (15 sec. steps)
Default: 60 sec.

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+ [F2], or by directly entering a value.

Note:  If "Optional features/Warning Tone" is set to "No", the 
       transceiver will not generate an "Alert Tone".

 TOT Pre-Alert Help
This selects the time at which the transceiver generates a "Pre-Alert 
Tone" before TOT expires.
TOT will expire when the selected time passes after a "Pre-Alert 
Tone".

Range  : Off(0) to 10 sec. (1 sec. steps)
Default: Off

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2], or by directly entering a value.

 TOT Rekey Time Help
This selects the "penalty" time in which the transceiver cannot be 
re-keyed to transmit after the TOT setting is exceeded.

Range  : Off(0) to 60 sec. (1 sec. steps)
Default: Off

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2], or by directly entering a value.

 TOT Reset Time Help
TOT Reset Time selects the minimum wait time allowed between 
transmissions that will reset the TOT count.
When this is set, the TOT continues even after PTT is released unless 
the TOT Reset Timer has expired.

Range  : Off(0) to 15 sec. (1 sec. steps)
Default: Off

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2], or by directly entering a value.

 Battery Save Help
This function is only for portable transceivers.
The Automatic battery save during standby operation, causes the 
receiver circuit to cycle ON & OFF to conserve battery life, except in 
the Scan mode.
The "ON" time is automatically selected by the current signal 
conditions.
The "OFF" time is selectable as [OFF], [Short], [Med] and [Long].
The transceiver cannot detect the carrier while the Battery save "OFF"
period. Recommend to consider the transmitting radio's TX duration 
should be longer than Battery save "OFF" period.

Range  : Off/Short(200msec)/Med(400msec)/Long(800msec)
Default: Off

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2].

 Battery Warning Help
This function is only for portable transceivers.

Enable :
 --- Low Voltage Warning ---    --- Battery Condition ---

    The red LED flashes         The battery voltage is low but 
    during transmission.        the transceiver is still usable. 

    The red LED flashes and     The battery voltage is too low and 
    a continuous beep tone      the transceiver is not usable 
    sounds while pressing       to make calls.
    the PTT.

Enable : The LED warning function, beep tone warning function and 
         transmit inhibit function do work.
Disable: The LED warning function, beep tone warning function and 
         transmit inhibit function do not work.
Default: Enable

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2].

 PTT Release Tone Help
This tone beeps when the PTT is released.

Yes    : PTT Release Tone sounds the receiving transceiver.
No     : No PTT Release Tone sounds.
Default: No

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2].

 Timed Power Off Help
This function is for mobile transceiver only.
Timed power off timer starts when the ignition is turned off.
After the timer expires, the transceiver will automatically turn 
off.
The timer will reset if the ignition is turned on and off.

Range  : off/1 to 8 hour. (1 hour. steps) 
Default: off

Note 1:  This function requires ignition sense.
         Connect the ignition-line to the connector which is located 
         at the rear of the transceiver.
Note 2:  If the ignition-line is not connected to the connector and 
         this parameter is set as 1-8 hour, the Timed Power off 
         function will perform.
Note 3:  After the timer expires, press Power switch to turn the 
         transceiver on.

Select the desired value by pressing [SPACE BAR], [Shift]+[SPACE BAR], 
[F2], or [Shift]+[F2], or by directly entering a value.

 End Of Help File

